Plan · Cost guide + estimator
What a deck costs, printed as a ledger — then computed from it
These are typical national planning ranges for 2026, stated with their assumptions. They are not quotes. The estimator below uses exactly the numbers in this ledger and nothing else, so you can re-check any result by hand — two worked checks are printed under the tool.
The printed ledger
| Item | Unit | Planning range | Assumptions |
|---|---|---|---|
| Deck, pressure-treated pine surface | per sq ft | $38 – $52 | Ground level, standard concrete footings, frame included |
| Deck, cedar surface | per sq ft | $48 – $66 | Ground level, standard concrete footings, frame included |
| Deck, composite surface | per sq ft | $62 – $85 | Ground level, 16 in. o.c. framing, standard footings |
| Deck, capped polymer (PVC) surface | per sq ft | $72 – $98 | Ground level, 16 in. o.c. framing, standard footings |
| Deck, tropical hardwood surface | per sq ft | $78 – $105 | Ground level; pre-drilling and stainless hardware included |
| Elevation adder, raised deck (about 4–8 ft) | per sq ft | +$9 – $14 | Taller posts, bracing, extra labour |
| Elevation adder, high deck (over 8 ft) | per sq ft | +$18 – $26 | Second-storey class: taller structure, staging |
| Railing, wood | per linear ft | $28 – $42 | Open sides only; house side excluded |
| Railing, aluminium | per linear ft | $52 – $78 | Open sides only; house side excluded |
| Railing, cable | per linear ft | $68 – $105 | Open sides only; tensioning included |
| Stairs | per step (riser) | $420 – $650 | Stringers, treads, stair guard and handrail included |
| Helical piers (in place of standard footings) | per pier | $340 – $480 | Pier count estimated at 1 per 55 sq ft, minimum 4 |
| Permits & drawings | flat | $450 – $900 | Permit fees plus a simple plan set |
| Pergola, small (to about 12×12 ft) | flat | $3,800 – $5,600 | Freestanding or attached, no canopy |
| Pergola, large | flat | $6,500 – $9,800 | Larger spans, no canopy or solid roof |
Not priced here, deliberately: demolition and disposal of an old deck, retaining walls, electrical runs, under-deck drainage systems, and solid-roof structures. Each is real scope with its own logic; a single blended rate for them would be a fiction. Railing length is computed as width + 2 × depth (the side against the house needs no guard).
The estimator
With JavaScript off, the estimator cannot compute. Plan from the printed ledger above instead: multiply your deck's square footage (width × depth) by the material rate, add the elevation adder if raised, add railing at width + 2 × depth linear feet, add stairs per step, then permits and any pergola. Every rate you need is in the table — nothing else is used by the tool.
Two worked checks, by hand
Check 1. 16 × 12 ft pressure-treated deck, ground level, wood railing, 5 steps, concrete footings, permits included, no pergola. Area 192 sq ft × $38–$52 = $7,296–$9,984. Railing 16 + 24 = 40 lin ft × $28–$42 = $1,120–$1,680. Stairs 5 × $420–$650 = $2,100–$3,250. Permits $450–$900. Total: $10,966–$15,814. Set the estimator to those inputs and it prints the same total.
Check 2. 20 × 14 ft composite deck, raised, aluminium railing, 7 steps, helical piers, permits included, no pergola. Area 280 sq ft × $62–$85 = $17,360–$23,800. Elevation 280 × $9–$14 = $2,520–$3,920. Railing 20 + 28 = 48 lin ft × $52–$78 = $2,496–$3,744. Stairs 7 × $420–$650 = $2,940–$4,550. Piers: 280 ÷ 55 rounds up to 6 × $340–$480 = $2,040–$2,880. Permits $450–$900. Total: $27,806–$39,794.
What moves a real quote outside the range
- Demolition of an existing deck and disposal fees.
- Site access — hand-carrying material up a hill is labour, priced as such.
- Regional labour rates — these are national planning figures; coastal metros run high, rural markets run low.
- Design complexity — curves, diagonal inlays, multi-level layouts and picture framing all add labour faster than they add material.
Turn a planning range into a real quote — request a connection